View source for HX2262 Remote encoder circuit

[[Category:English pages]]
[[Category:Electronics]]
[[Category:Elektronik]]
<google>HX2262-HX2272</google>
HX2262 is equivalent to PT2262
* [[Remote controlled switch with HX2262 and HX2272]] look what's inside.
* [http://www.princeton.com.tw/downloadprocess/downloadfile.asp?mydownload=PT2262_1.pdf  PT2262 Datasheet]
* [http://www.datasheetcatalog.net/cgi-bin/helo.pl?text=PT2262 PT2262 Application note]

===1. Description===
HX2262 is a remote control encoder for encoding signals to be decoded by the [[HX2272 Remote decoder circuit]].
It encodes data and address pins into a serial coded waveform suitable for RF or IR modulation.
HX2262 has a maximum of 12 bits of tri-state address pins providing up to 531,441 (or 312) address codes; thereby,
drastically reducing any code collision and unauthorized code scanning possibilities.

===2. Features===
* Low-power CMOS technology
* Low SNR
* Up to 12 Tri-State code addresses pins
* Up to 6 Data pins
* Operating voltage range: 3 to 18V 
* Instantaneous or output latch
* DIP package
* RC oscillator 

===3. Applications===
*Car security system home security / automation system
*Garage door controller
*Fans remote home security / automation systems 
*Industrial remote control
*Toys with remote control

===4. Pinout===

{|width="100%"  border="1" cellpadding="2" cellspacing="0"
|-
!style="color:#ffb900"|Pinout<br>18-lead package
!style="color:#ffb900"|Pinout<br>20-lead package
!style="color:#ffb900"|Pin name
!style="color:#ffb900"|Input/Output
!colspan="2" style="color:#ffb900"|Note
|-
|1 ~ 6
|1 ~ 6
|A0 ~ A5
|I
!colspan="2"|
Code Address Pin Nos.0 ~ 5
These six tri-state pins are detected by HX2262 to
determine the encoded waveform bit 0 ~ bit 5.
Each pin can be set to “0”, “1” or “f” (floating).
|-
|7 ~ 8 10 ~ 13
|7 ~ 8 12 ~ 15
|A6/D5 ~ A11/D0
|I
!colspan="2"|
Code Address Pin Nos.6 ~ 11/Data Pin Nos.5 ~ 0.
These six tri-state pins are detected by HX2262 to
determine the encoded waveform bit 6 ~ bit 11.
When these pins are used as address pins, they
can be set to “0”, “1”, or “f” (floating).
When these pins are used as data pins, they can
be set only to “0” or “1”.
|-
|14
|16
|TE
|I
!colspan="2"|
Transmission Enable.
Active Low Signal. HX2262 outputs the encoded
waveform to DOUT when this pin is pulled to low.
|-
|15
|17
|OSC1
|O
|
Oscillator Pin No.1
| rowspan=2 style="border-bottom:3px solid grey;" valign="top" |
A resistor connected between these two pins determine the fundamental frequency of the HX2262.
|-
|16
|18
|OSC2
|I
|
Oscillator Pin No.2
|-
|17
|19
|Dout Pin
|O
!colspan="2"|
Data Output Pin.
The encoded waveform is serially outputted to this
pin. When HX2262 is not transmitting, DOUT
outputs low (Vss) voltage.
|-
|18
|20
|Vcc
| --
!colspan="2"|Power positive
|-
|9
|9
|Vss
| --
!colspan="2"|Power negative
|-
| --
|10 ~ 11
|NC
| --
!colspan="2"|--
|}

[[Image:HX2262 package.jpg]]
[[Image:HX2262 pinout.jpg]]

[[Image:HX2262 application.jpg]]

<google>HX2262-HX2272</google>